All Installation Instructions for Maytag Range CDE8520ACB

Lefrt Front Burner Quit Working

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

Parts Used:

Surface Burner Switch - 240V

Jerry from Sedro-Woolley, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

After a lighting storm the oven would not work it kept blowing the range fuse it was determined by a friend it ws the selector switch

first removed the four screws that held the panel in place, tthen unscrewed the actual switch itself. I then pulled the wire, one at a time from the old switch and pluged the wire in to the new switch. upon completion I tested the oven selector switch and secured the switch in place, then replaced the panel. And I'm up and running again!

Parts Used:

Selector Switch

Janice from Pawtucket, RI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Any setting selected (1 thru 9) would result in the surface burner going to full hot

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Parts Used:

Surface Burner Switch - 240V

Randall from Eureka, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No leveling legs

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Parts Used:

LEVELER

stephen from montgomery, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

time to replace the filter

lift out old filter, wash, put in new filter.

Parts Used:

Grease Filter

Karen D from Columbia, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Grease filter needed replacing

Remove old filter- put in new filter. EASY!!!!!!!!

Parts Used:

Grease Filter

Freda from Elizabethtown, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced grease filter

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

Parts Used:

Grease Filter

Light Bulb - 40W

Gregory from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

filter was deteriorated from 15 plus years of use

lifted the top center panel off removed old filter installed new easy peesy

Parts Used:

Grease Filter

Steve from Marshall, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Grease filter clogged and in need of replacement

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.

Parts Used:

Grease Filter

Mark from STAUNTON, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old one was plugged

Pulled out old one and slipped in the new one.

Parts Used:

Grease Filter

Rudy from GARIBALDI, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed replacement oven rack.

Part was perfect fit. Good product, good value, great service.

Parts Used:

Oven Rack

Bobby K. from Huntsville, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner control stopped functioning.

Replaced the control.

Parts Used:

Surface Burner Switch - 240V

Kenneth from GAITHERSBURG, MD
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

switch went out

removed the two screws that hold the switch unit into the housing that sits on top of stove. Noticing the electrical connections, I secured the power to the oven by shutting off the circuit breaker. I then removed the faulty switch from + and - wire connections and cleaned and reconnected wires to the new switch and slid new unit back into upper housing and put the screws back in to hold it in place. I turned the power back on, toggled the switch, and heard the ventilation fan whirl. Piece a cake. So gald I was able to find the part. Teddy Schoewe, Winona, Mn.

Parts Used: