All Installation Instructions for Maytag Range CDE8300ACB

Lefrt Front Burner Quit Working

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

Parts Used:

Surface Burner Switch - 240V

Jerry from Sedro-Woolley, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

time to replace the filter

lift out old filter, wash, put in new filter.

Parts Used:

Grease Filter

Karen D from Columbia, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Any setting selected (1 thru 9) would result in the surface burner going to full hot

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Parts Used:

Surface Burner Switch - 240V

Randall from Eureka, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

switch went out

removed the two screws that hold the switch unit into the housing that sits on top of stove. Noticing the electrical connections, I secured the power to the oven by shutting off the circuit breaker. I then removed the faulty switch from + and - wire connections and cleaned and reconnected wires to the new switch and slid new unit back into upper housing and put the screws back in to hold it in place. I turned the power back on, toggled the switch, and heard the ventilation fan whirl. Piece a cake. So gald I was able to find the part. Teddy Schoewe, Winona, Mn.

Parts Used:

Fan Switch

THEODORE from WINONA, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

replaced grease filter

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

Parts Used:

Grease Filter

Light Bulb - 40W

Gregory from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Needed replacement oven rack.

Part was perfect fit. Good product, good value, great service.

Parts Used:

Oven Rack

Bobby K. from Huntsville, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Grease filter clogged and in need of replacement

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.

Parts Used:

Grease Filter

Mark from STAUNTON, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Range oven door switch need replaced

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

Parts Used:

Light Switch

Ruth from Gastonia, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

filter was deteriorated from 15 plus years of use

lifted the top center panel off removed old filter installed new easy peesy

Parts Used:

Grease Filter

Steve from Marshall, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Grease filter needed replacing.

Removed old filter and replaced with new.

Parts Used:

Grease Filter

James from BEND, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.

dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.

Parts Used:

Range Burner Cartridge Terminal Block

Cartridge Male Contact Spade

Ge from Solon, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Grease filter needed replacing

Remove old filter- put in new filter. EASY!!!!!!!!

Parts Used:

Grease Filter

Freda from Elizabethtown, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The 6in burner would go to max heat regardless of the setting.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Parts Used:

Surface Burner Switch - 240V