CC2S985SET5SS General Electric Range - Instructions

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

I removed oven door so i could reach easier. Then removed screws from Broiler element at the back of the oven. Pulled off connected wires. Slid wire connectors on new element and screwed bracket in.

every thing went great

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.

I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,

Order parts and installed - no tools needed - completed repairs less than 1 minute

Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Removed two screws, and replaced element with a new one. Easy, works great.

Followed the video and it was fast and quick.

I JUST EXCHANGED THE BURNER AND BURNER CAP.