CAV1000AWW Magic Chef Washer - Instructions

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Took the whole machine apart tipped tub upside down to put on snubber ring. One person had to hold down very very firmly to the metal ring that fits on top of the snubber ring while another person quickly screwed in the screws to hold it down.
The springs required an extra strong person and a few words of frustration to stretch to get them on. My son who is 39 years old did it. My 60 year old husband would not have had the strength to stretch the springs.
So far it works great. My son washed his carheart jumpsuit and coat with not a sound or wiggle. Your trouble shooting site was what made us decide to order what we did because of the percentages of what the problem was beside each part. Thank you for being so prompt in sending our parts.They came so quickly we weren't without a washer but maybe a day or two.

First I pulled the washer to an open area.
Then removed fluid line going to tub.
Removed tub by removing springs.
Turned tub upside down, removed the belt pulley, and held the ring under the snubber ring with C clamps while removing 6 screws holding assembly together. Released the pressure on the C clamps slowly until spring pressure was gone.
Replaced snubber, and installed ring holding assembly. Replaced ring plate, and C clamps going back in place with equal pressure until seated. Replaced 6 screws, and pulley assembly, and all fluid lines and new spring kit.
WALA..... WORKS GREAT for less than $25.

Thanks

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

Unpluged washer,moved from wall,unclip upper assembly&support it. Remove LITTLE acess panel on rear and front panel. Removed springs & two hoses,drive belt and out it comes...flip unit over to LOOSEN ONLY 6 sdcrews to remove old snubber & install new one. Reverse procedure to reinstall. BE WARNED,springs can be a sob to reinstall!unit),The acess on rear to springs is horrible!

The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.

The PartSelect video was excellent and very helpful. This replacement took extra time because the washer was located in a tight space and moving/lack of access to the rear of the washer created several issues. Tips based on my experience:
1) I used a MasterLock ratchet tie-down to secure the lid when raising the hinged top of the washer (I wasn't able to lean and support this against a wall as demonstrated in the install video).
2) The fill hose that connects to the water valve was difficult to remove and I needed two large-jaw adjustable pliers to do this. A small amount of Dawn dishwasher detergent applied to the inside of the hose made re-assembly quick and easy. 3) A set-screw holds the valve in place. Easy to remove but because I couldn't get in back of the washer, I had to measure from the bottom of the valve to line-up the screw with the hole in the valve assembly to mount the new unit (this wouldn't be a problem if you could see where the screw goes but I couldn't get in back of the washer for this simple final step). Very pleased with finished result - just needed some extra time and additional tools.

Mostly I followed the video instructions from partselect's youtube channel. The snubber is very simple to replace. Once the tub is removed, the snubber drops down around the hole and the tub gets put back. The springs hold the tub down, and need to be removed. They are a challenge because they are very strong. The vice grips come in handy to grab the springs and hold them. The best trick I've seen for doing the springs is to use about 10 nickels. When installing the spring, bend it and place the nickels in the spirals of the spring, alternating sides with five going in the left and five in the right. When you go to put the spring in, it will be expanded so it almost fits the distance, and there's less required to pull it into place. Once in place, some nickels fall out and the rest can be removed easily. It also helps to have a second person who can push the tub towards the spring you're trying to install, to make the distance smaller.

Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.

Followed the great instructions on your video

Repaitmr was simple. Followed video instructions from web site. Problem I ordered wrong motor so it just blew my plugs fuse. Also needed pump. Changed motor to old motor installed new pump. Machine works great.

raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.

I changed the piece easily

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.