All Installation Instructions for Crosley Range C31315VBV

F 3 signal on display pad every time oven warmed up

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

Parts Used:

Short Oven Sensor Kit

jeff from haskell, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Had an F2 message go off then F3 when I tried to turn the stove on

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

Parts Used:

Short Oven Sensor Kit

Daniel from MOUNT HEALTHY, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

oven would not turn on

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

Parts Used:

Flat Style Oven Igniter Kit

Robert from Clymer, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Original burner was eroded on the bottom and flame was coming from undernealth the burner

Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.

Parts Used:

Sealed Burner Cap with Electrode

Joe from Staten Island, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

corroded burners

Unscrew the burners an install new ones! Anyone could do this.

Parts Used:

Sealed Burner Cap with Electrode

Daniel from Can Francisco, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Replaced burner

Went well

Parts Used:

Sealed Burner Cap with Electrode

Ramiro from Bernalillo, NM
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

I needed a broiler pan

I took the broiler pan out of the shipping container and put it in the oven.

Parts Used:

Broil Pan Insert

Broiler Pan

Rhoda P. from Secaucus, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Bad Gasket

I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

Parts Used:

Sealed Burner Cap with Electrode

javier from Santa Ana, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Stove Would Not Light To Heat Up.

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

Parts Used:

Flat Style Oven Igniter Kit

Nola from Enid, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

oven would not heat up fully, smelled of gas.

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

Parts Used:

Flat Style Oven Igniter Kit

Brian from Spotswood, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Missing gasket under burner caused gas to leak out

I followed the video and it was incredibly easy. I shut the breaker off (we live in an apartment, and pulling the plug on the stove wasn't possible). I lifter out the old burner (the gasket underneath was corroded, and I just threw it out, as the newer burners are self-sealing); removed both the igniter wire and the ground wire (I needed a pliers to tug the igniter wire off); attached the new burner; replaced the burner; turned on the power; and voila!

Parts Used:

Sealed Burner Cap with Electrode

James from NEW YORK, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

BURNER DID NOT IGNITE. HOLE ON SIDE OF BURNER HAD A HOLE, SO FLAME WAS UNEVEN.

USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.

Parts Used:

Sealed Burner Cap with Electrode

Kenneth from WATSONVILLE, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

oven would not light reliably.

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

Parts Used:

Flat Style Oven Igniter Kit

Joe from West Winfield, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Igniter for oven not working

Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!

Parts Used:

Flat Style Oven Igniter Kit