All Installation Instructions for C301

old yucky filter

Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!

Parts Used:

Range Grease Filter

Diane from Flower Mound, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The stem of one of my burner switches broke off so I had to replace the switch.

Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.

Parts Used:

Surface Unit Infinite Switch Kit

John from Fulton, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Wife left burner on

Replaced switch.

Parts Used:

Infinite Switch

Alan from Alpine, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

uneven/intermittent burner heating

shut circuit breaker, remove two screws, lift knob panel, move wires to new switch, remove and replace switch, clean surface

Parts Used:

Surface Unit Infinite Switch Kit

Kelly from Alameda, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

front burner would only work on high

Installed the part------very easy

Parts Used:

Surface Unit Infinite Switch Kit

william from cairo, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner switch would only stay on hi

Replaced the switch.

Parts Used:

Infinite Switch

David from Willow Grove, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

0 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The paint had chipped and peeled on the inlet grill

I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!

Parts Used:

Vent Cover - Black

Ann from Irvington, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Holes in the air filter of our Jenn-Air grill

Simply pulled the old filter out and put the new filter in.

Parts Used:

Range Grease Filter

Janice from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

grease filter was disintegrated and burner knobs were illegaible

Installed the new filter and replaced the knobs in about a minute. Customer service helped me find the right parts for an over-35-year-old unit and the installation of them was elementary and took probably less than a minute. I am in business again, cooking for my family; and my visiting relatives can cook without guessing the temperature (previous knobs were illegible. Recommend this site without reservation. (Received the parts in about 2 days!). A real treasure of a save!

Parts Used:

Surface Burner Knob

Range Grease Filter

Jeanne A from Sonoma, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Could not read numbers on the knobs

Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.

Parts Used:

Surface Burner Knob

Bill from ROCKLEDGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner Knobs worn and bent

Placed new burner knobs onto cooktop. easy

Parts Used:

Surface Burner Knob

Linda from Cadiz, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Filter worn out, exhasut fan kept going off

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Parts Used:

Range Grease Filter

John from Cayce, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Off-on switch would not turn burner on

Turn off power to cooktop. Lift the broken infinite switch knob off the switch console. Use pliers to remove the hex nut that is under the knob. Then remove the grill over the exhaust vent to expose the two screws that hold the switch console in place. Using a philips head screwdriver, unscrew the two screws and lift the console up as far as the wiring will let you. Push the two little clips on either side of the electrical component you want to replace, to release it from its harness. Pay attention to the wires of the broken switch and pull one off at a time and attach to the new part. I used a knife to pry the wires off the electrical pins. Once all wires are reattached, clip the component into the harness and attach the hex nut back onto the protruding d-stem. Put all back together and test the switch before turning power back on. If ok, turn power on and test again.

Parts Used:

Surface Unit Infinite Switch Kit