C200 - Instructions

Gordon from Annapolis, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

old filter to replace

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

Parts Used:

Range Grease Filter

Colette from Baton Rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

old, crusty drip pans

This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John

Parts Used:

John from Richardson, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

install burner drip pans

Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.

Parts Used:

Warren E from Newport, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Numbers on surface burner knobs were illegibel.

I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.

Parts Used:

Wayne from NEENAH, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Change the Oil/Grease Filter

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Parts Used:

Range Grease Filter

Yong from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Knobs were worn badly

Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.

Parts Used:

Royce from Garland, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Old stove drip bowls needed replacing

Removed heating elements and dropped new drip bowls in and replaced new elements

Parts Used:

Delta Frame Surface Unit - 8 Inch

Delta Frame Surface Unit - 6 Inch

Alfred from Fayetteville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Frayed and exposed receptical wires in cartridge

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

Parts Used:

Surface Burner Receptacle Kit

Richard C from San Jose, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

old burners, burning very uneven!

Pulled out the old, plugged in the new

Parts Used:

Delta Frame Surface Unit - 8 Inch

Robert from Falls City, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

surface switch was bad

just swapped out the two switches

Parts Used:

Surface Unit Infinite Switch Kit

Arthur H from Irving, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

my old knobs were so worn that I couldn't see the numbers

I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!

Parts Used: