Models > BISB42ELB > Instructions

BISB42ELB General Electric Refrigerator - Instructions

All Instructions for the BISB42ELB
91 - 98 of 98
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Ice Bucket had rusted
It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!
Parts Used:
Auger and Ice Bucket Assembly
  • Leticia from El Paso, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Auger and Ice Bucket for GE side by side was rusty
followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!
Parts Used:
Auger and Ice Bucket Assembly
  • Jay from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Parts Used:
LIGHT SWITCH
  • christopher from collegeville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bucket was broken at the back where the auger turns.
Removed the bucket assembly from the freezer. Remove the four screws holding the front cover on the bucket. They are on the backside of the front cover. Installed the old front cover on the new ice bucket with the four screws.
Parts Used:
Auger and Ice Bucket Assembly
  • Ernest from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Parts Used:
Auger and Ice Bucket Assembly
  • Steve from Canyon Country, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Parts Used:
Auger and Ice Bucket Assembly
  • Frank from Temecula, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no water to ice maker or water dispencer
replaced circuit board and water solenoids
Parts Used:
Auger and Ice Bucket Assembly
  • craig from sweeny, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rusty Auger
The parts recommended were exactly what I needed. The comment section on not paying attention during the removal were very helpful. I took a picture before totally taking everything apart. Thanks for the added comment.
Parts Used:
Ice Dispenser Bucket Ice Bucket Auger Kit
  • James R. from San Clemente, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the BISB42ELB
91 - 98 of 98