BAFW3577KB0 Frigidaire Washer - Instructions

Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.

love parts select have used them several times for parts great company

Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.

Remove screws take off striker .Put striker back on with screws back on

Tighten screws. Took 5 minutes

Remove top of washer, remove door lock assembly,install new assembly replace top.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

My shocks on the washer were broken, in part because of age, the other is broken spider drum inside the barrel. Was very easy to do the shocks. Unhook water connections and power. Move washer away from the wall. Remove the back cover from the washer. On the left side, you have to remove two screws from the electronics control box so you can gently move it out of the way. Then grab the plastic pin with some pliers and pull while depressing the locking lug on the end of the pin (Very important to depress the lock or you will have to buy new pins) Remove both pins for each shock. I used some high pressure grease on the pins when I put it all back together. Was a quick fix. Unfortunately had to take it all back apart as this was only a small part of my issue with having the stainless drum being broken inside.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

First I removed the two screws that hold the part in place. I then pulled the part out about 3 inches and disconnected the three wires from the part and put the new one in

replaced the two shocks with the new ones by removing the pins that held the old ones in place.

Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

Replaced drain pump using this walk through. Different models, but pretty straight forward.

The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.