BAD1 Frigidaire Dishwasher - Instructions

I removed the kick panel at the bottom front of the dishwasher. Then using a flashlight and a cross point screwdriver, I removed the thermostat from about the middle left. It requires a short screwdriver, but not quite as short as a stubby. I unplugged the wires, noting that one of them was a little burnt looking. The burnt looking connector was still okay. I then installed the new one, with the green dot on the thermostat having the slightly burnt looking connector. Then I ran a load of dishes and the dishwasher worked as it was supposed to. It has worked okay twice since then.

I watched several videos of people replacing this gasket easily, but we had trouble. The old one came out easily. The new one just slipped into the crack, but it kept going and ended up on the inside of the door. We ended up taking the outside panel off to get the gasket out. We tried to fit the thing into the slot, but it kept coming out the other side. I finally came across someone who had had the same trouble. By feel only, you can feel a slight ridge on the top side of the lower door and I had to press the gasket against that ridge. It was not a very noticeable ridge, but it holds the back (slot edge) against the door so that the gasket stays put. When we figured that out, the repair went smoothly. I am running the dishwasher now and so far, so good.

1 Removed 2 screws to remove door panel so as to access back of dispenser.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.

Reversed these 3 steps to install new unit.

Easy. Don't even think of calling the repairman.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.

Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!

I read the instructions that others had posted and completed the repair in less than 5 minutes!

I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

Completly disconnected and layed dishwasher on its side for better access. New valve support was 1 inch longer than original but created no problem. it took no more than 30 min. to complete job.

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

Pulled off the old gasket and replaced it the same way with the new one.

This repair project was easy enough that my 15 yr old son had it almost all done without me. The hardest part was getting the wires unplugged from the old latch. Once we got the pliers out to help us get a grip, everything went smoothly!
This was a quick and easy fix for an older dishwasher that still works!

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!