B1EIN1601B ((01)) Bosch Dishwasher - Instructions

I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

To perform the repair, the door panel must be removed (8 Torx screws) and the door removed from the hinges in order to access the lower door seal. For this model Bosch and other similar models, the hinge springs must then be disengaged (safer) or kept from retracting. To disengage the springs requires removing the entire unit, disconnecting the water supply, and flipping it on its side to disengage the springs. I chose the latter, keeping the unit in place, holding the hinges with vice-grips on either side, then removing the door. This was not easy and caution is required. Either method is risky with a 20-year dishwasher.
The replacement part does not fit as well as the original (much sturdier) part, but appears to seal well for now. Repair videos on the internet are for different, newer models where disabling the hinges as described here is not required, making the repair much easier. Recommend looking carefully at your model/manual to determine if the difficulty of the repair is easy or hard.

There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't involve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.

I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.

There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.

Vice grip door hinges. No need to disconnect, un hook hing springs. Works slick. Small vice grips. On hinges. Remove tore screws. Remove seal , and replace seal, reconnect door screws. Boom done.

REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.

Followed the video on your site and it was an easy install with no more leakage.

Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.

I snapped the part in and voila!

Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.

Dishwasher door won’t stay closed. Upon inspection, the metal striker/catch at the top of the door was broken. This dishwasher is 12 years old and this is the first problem I’ve had with it. To repair the catch, first remove screws holding cover plate at the bottom of the door. Next, remove screws holding the dishwasher stable from under the counter. The pull out the dishwasher to gain access to the catch. You’ll have to take a small set of pliers and bend the two tabs back that hold the catch in place. Lift the catch up and forward to remove. Replace and bend the tabs back to hold the new catch securely. Move the dishwasher back in place and secure with the screws previously removed. Put the cover plate back in place and you’re done.

shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done