ATW4516MW0 Admiral Washer - Instructions

I popped the cap off of the agitator. I could see the grabbers weren't grabbing the side of the agitator. I thought I could take a shot at fixing it since I was ready to give up. Happened upon this site. With the model number, I was very easily able to find the parts I needed. Ordered them up. Took one bolt out of the assembly and the whole agitator came off. I popped in the new parts as the diagram was very easy to follow, resecured the bolt, and all was good. I saved a ton of money off replacement or even calling a service tech. Your site made this very easy with the detailed diagrams. Didn't order anything I didn't need. Only cost $11 to fix it and made me feel like Mr. Fixit. I will definitely use your site as my first, best choice for any problems I have in the future.

took out old agitator and installed new one, machine now runs like new. couldn't be happier.

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Replaced agitator sprage kit. Simple instructions simple repair

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Tip the washer on its back remove the agitator install new one under 15 minutes

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I ordered a whole agitator repair kit. Had a few problems getting everything to line up right.Finally figured out what I needed to do and everything worked like it should.

I ordered the part and watched the installation video. It would have helped if I had watched the video all the way through at least once. Instead I paused and restarted it as I did the repair. As a result I had a hard time putting the agitator back together. Otherwise it was a fairly easy repair and my 20-year-old washer works great again!

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

Removed top agitator bolt lifted agitator out and replaced ring and geared dogs. replaced Agitator top swirl vanes. It would have been nice if the kit included agitator grease and a new bolt and washer.