ATF7000FS1 Frigidaire Washer - Instructions

"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.

For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!

With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.

Pulled the locking pins out, replaced the shock absorbers and re-installed the locking pins. I used Channel Lock pliers to remove and replace the locking pins. i used a deep socket to hold down the tab on the locking pins so they could be pushed out. The new shock absorbers came with installation instructions.

I removed 2 screws from the the top back of top. Removed the cover. Removed the 2 screws holding the door lock assembly.Removed the door lock assembly, disconnected the 3 wiring harnesses. Connected the wiring harnesses to the new door lock switch assembly. Installed the new unit in the door lock, reinstalled the top.Done.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.

Removed the 4 screws holding the top on. Pulled top forward to release front catches and stood top up out of way. Removed 2 screws holding door lock. Could not unplug wire plugs from door lock because wires too tight. Removed 2 screws holding lower front panel and removed panel. Pulled door lock down and unplugged old lock and plugged in new lock. It was easier to position door lock to reinstall screws by working from top, so top removal wasn't a total waste of time. Reinstalled front panel and top. Machine works.

It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!

Removed front panel and unplugged wire connector to drain pump. Loosened two hose clamps and removed hoses the unbolted drain pump from washer frame. Simple removal and even simplier installation of new drain pump.

Replaced drain pump using this walk through. Different models, but pretty straight forward.