AS2125SIHW Maytag Refrigerator - Instructions

First I removed the drip pan, then removed the two screws behind it which hold the frame. I then pushed up on the frame, the top of which is slotted to fit on two large-head screws. This allows the frame to be swung loose. I then disconnected the flat control cable, then removed two more screws. Replaced ice chute door, but repair didn't work. Repeated this several times. The problem was that I had not correctly affixed the part holding the door to the solonoid pin. The pin had dropped out, and I re-inserted it the wrong way. Be sure that the slotted end of the pin properly engages the chute door holder. This job would have taken much less time if I had more carefully examined the mechanism while disassembling it. Next time I repair something, I'll use a digital camera to snap a few pictures as I disassemble the mechanism.

I followed the instructions from other users and everything went fine. I had one issue not covered. My refrigerator doors are covered by cabinet panels, and the top panel had to be removed in order to remove the panel for the ice/water dispenser. The part was perfect and fairly easy to install!

it was a cake walk,removed a few screws unpluged assembly installed new switch didnt get shocked, nothing started on fire, ice came out like it should afterwards

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]

Obtained the part from part select in record time. Exact part arrived next day and changed out the faulty part within an hour. great service and have already booked-marked the website should future appliance parts be needed. Fair price too!

Disassembled the control facade of the ice maker/water dispenser, then attempted to install the chute cover, only to discover that an arm connecting the chute was broken. Temporarily reassembled the chute with cover, so we can still secure water. Will need to order broken arm to finish the install.

Removed 5 screws, took unit apart, replaced part, put back together. Just be sure to have the solenoid connected to the ice door lever the right way before you reassemble.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

it went just fine. fowed instuctions from web page. 1,2,3,done
thank you

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

it looked like it wouild be a pretty quick job, so i didn't take any chances; i unplugged the fridge to avoid any chance of problems with circuit board behind front facing. removing "drip catcher" at base of opening reveals 2 torx screws (easily removed) and two more up near the chute opening and light bulb. front facing then easily lifts off. i found it easiest to unplug ribbon cable from the circuit board. The door itself is pretty self-explanitory as how to remove and replace. the trick was figuring out the correct position for the attaching solenoid. it's supposed to be in a "normally out" position under the attaching part of the door flap mechanism. and that was it. much easier than i expected. it took about 15 minutes.

I first read the repair hints on your web site and proceeded to follow the instructions that were there. This was a very easy fix and did not take long to repair. I did get a bit of an electrical shock when I accidentally touched the electronic board with the back of my hand. But again, the instructions are very helpful and anything that I would add for instructions would just be repeating what others have said.

Poped ou the old switch, connected new switch and pushed back into socket.