ARTE105BC Amana - Instructions

I pulled the frige out, took off the cover from the bottom with a nut driver. Took off the safety clip then pulled the plug out from the relay then the relay came out. Replaced the part and reinstalled the same way. This was really easy and fast.

Apparently, the manufacturer sometimes substitutes a part but keeps the same number, which is what happened here. The part wouldn't fit in the actual space on this model--even though the number was apparently correct! Refunding my money and assisting me to contact the manufacturer directly couldn't have been easier! Impressive customer service in a difficult situation.

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

Unplug Refrigerator remove lower back panel to expose compressor.Unplug Capactor relay assembly,Plug in new start assenbly,and then the refrigerator to elect'outlet .Compressor srarted right up . Real easy fix simple tools to perform change out. Thanks!!! Saved a bunch of $$$$$ .

I removed the cover panel. There is a clip that holds the relay and capacitor to the pump. Use a screwdriver to pry it off. Unplug the relay. The capacitor is plugged into the relay and they come together which was a surprise, I thought I only ordered the relay. Unplug a cable from the relay. Insert that cable into the new relay and plug it into the compressor. Reattach the clip. One be important instruction. Unplug the refrigerator for at least 8 hours before installation to allow the compressor to cool down. I tried first without allowing the compressor to cool and it did not work. After letting it cool I tried again and it worked like charm. Make sure the refrigerator is unplugged when doing the repair

After unplugging the refrigerator, I removed the lower rear access panel that exposed the condenser and the overload/relay start capacitor with 1/4" nut driver (6 total). Next, I unplugged the wire harness and spring loaded keeper with needle nose pliers. Then I pulled the overload/relay start capacitor out of the 3 pronged male receptor located on the side of the condenser and plugged in the new one. Replaced the keeper, plugged the harness back in, and replaced the panel. Very easy fix.

Viewed the viedo - it showed what to do

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me

Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

First off I had no idea how a fridge worked or where to begin and the troubleshooting section of the manual was a joke. So I took the back panel off made sure the coils underneath were clean. Took out the back panel of the freezer and made sure that nothing was frozen over and I hadn't seen excess water on the floor so ruled that out. I knew the condenser was still running so I took a shot in the dark. Ordered the part and waited for it to arrive. It took me 3 minutes to open the box and install it. Immediately knew it was working replaced the back panel and moved the fridge back.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00