All Installation Instructions for Refrigerator ART308FFDB00

freezer and refrigerator compartments not cold enough

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Parts Used:

Refrigerator Capacitor

Michael from Colorado Springs, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Light rocker switch broke and refrigerator light couldn't go on.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Parts Used:

Refrigerator Door Switch

Cathy from HOPATCONG, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Freezer occasionally had a temperature alarm.Clicking noise also.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Parts Used:

Refrigerator Capacitor

Barry from FORD CITY, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Fan was not spinning make it not cold in bottom part

Take screws out pull panel out unconnect the part connect new one and your done

Parts Used:

Freezer Evaporator Fan Motor

Dylan from WHEELING, WV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

GASKET AROUND DOOR WAS LETTING AIR IN/ COLD AIR OUT

Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!

Parts Used:

GASKET-DOR

Susan from BONNEAU, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

light did not work on the refrigerator side

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Parts Used:

Refrigerator Door Switch

David from GROVESPRING, MO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Rocker on switch broke off

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Parts Used:

Refrigerator Door Switch

David Barnes from ROSWELL, NM
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light switch broke off

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Parts Used:

Refrigerator Door Switch

Kathy from TEMECULA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Did not have ice maker

Followed online video instructions

Parts Used:

ICE MAKER FIELD INSTALL KIT (T

Marisa from TEMPE, AZ
Difficulty Level:
Very Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used: