AMV6507RGS3 Maytag Microwave - Instructions

screwed in new bulb

Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.

Husband replaced the bulb

Repair unsuccessful because they sent the wrong part, even after I questioned their selection. It is amazing how a company as large as Whirlpool cannot clearly indicate to the people who work for them how to order the correct part. The fault lies not in the individual who is putting the order in but with the company who cannot take the time to make sure that person is successful in completing their job. Will never buy a product from this company again.
As far as the shipping is concerned. It took forever, just to find out that the part was incorrect.
Better luck next time. right?

Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!

Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.

Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.

Overall a very simple repair.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

I had to cut the leads on the thermostat to enable the wire terminal clips to fit on the leads. Not hard at all when the right tools are available. Care must be used because the leads are subject to being damaged. “ Hold leads with narrow needle nose pliers while cutting!

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

took a chance on this was the problem and it was...my son-in-law took it out put in the new one and it worked...saved $300

I had the help of a handyman, I'm 75 years young but not handy with tools

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul