AMKIT97 (4344173) Whirlpool Ice Maker - Instructions

Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.

Your youtube ..order part and fix in 2 mins.AWESOME we had our refrigerator since 1983.... my wife keeps her looking new...& happy with the saving .Our frigerator a MAGIC CHEF..the ice maker is the only thing we have replaced.

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.

Turned off ice maker. Remove one screw with nut driver (1/4") that hold plugin cover. Push the release lock, (up) on bottom of Ice maker to slide unit out enough to unplug and remove ice maker out of freezer. remove white side cover and replace control unit. Reinstall white side cover then plug unit in at freezer and slide unit into locks reinstall plugin cover with screw. Turn on ice maker and watch Ice maker start to move and tray to fill with water. Done.

Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.

Removed old ejector arm and installed new part.

First I disconnected the refrigerator. I snapped off the service door. taped closed the auto.door shut off located on the left side wall. the unit just pulled out,
disconnecting the power source, removed the plastic cover, unscrewed (3) screws and reattached the new unit . i reconnected the process in reverse.
if i had repairman do this it would have cost twice as much .

Took the ice maker out with three screws hving turned water off and unplugging fridge. Put a new one back in with the three screws. plugged fridge back in and turned water on. All done and everthing worked fine.

Ronald Stonis

Did not have to remove the complete ice maker. Only the front part that housed to motor assembly. Two Clips removes to cover and three screws removed the motor unit and the rest was in reverse. No wires to disconnect or connect. It just plugs in to unit. Works great and cheaper than from Sears Parts Direct shipping cheaper also. Will buy from Part Select again.
Thanks, Ron

First I did the diagnostics and thought the water valve wasn't functioning so I replaced that, but it still didn't make ice. So I went on line and found the first thing to fix should have been the module and motor assembly. It was a real easy fix because I had pulled the ice maker before to investigate what was wrong. I just removed one screw and disconnected the electrical. There were four screws holding the motor assembly on. So I put the new motor on and had ice in 30 mnutes.

Unplugged the refrigerator. No need to remove the entire icemaker (IM). Removed the old module by taking out the 3 screws and carefully wiggling it free from the icemaker. Lined up the blade arm with the new module, pushed the module onto the IM and put in the 3 screws. Lowered the shut off arm and plugged in the refrigerator. Once the freezer compartment reached the proper temperature, the IM began making ice with no further problems.

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

After reading the stories on your site, I figured it had to be the motor control. Easy to take off, but had to take the tray off the freezer wall to get the ice out. Once I did that it was a piece of cake. Now I have ice (and vodka tonics...).

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Note: I thought the motor was bad, it was actually one of the gears. Order the motor-gear module. You will probably receive the motor-gear module if you order the motor only.

I removed the hex bolt on the right side of the ice maker. Removed the whole assembly from the refrigerator, diconnecting the cable as I pulled it out. I use a philips screw driver to remove the three scews holding the motor gear assembly. I pulled off the motor/gear module; installed the new motor gear assembly. Reinstalled the ice maker. Easy!