AMKIT97 Whirlpool Ice Maker - Instructions

Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.
Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!

I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks

first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!

Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.

Took the front of the ice maker off. Noticed the arm inside was broken, found the part on your site and ordered it.....super fast delivery. Replace the moter assembly and off she went. had ice in about 30 minutes. Thanks for your services and I will highly recommend you to others......Thanks again.

followed instructions provided when ordering part

Installed new motor control

I first turned off the refrigerator. I then used a hair dryer to melt and release the ice by warming the bottom of the mould. Then I turned the fridge back on and let the icemaker discharge the ice. I then turned off the icemaker and ordered the new part. I unplugged the fridge, removed the icemaker (three screws and an electrical connection). Then I replaced the heater/tray with the new one and turned everything back on. Within a couple of hours we began having ice again.

The ice maker had quit before and I fixed it by taking it out to thaw.When it quit working the second time thawing it out didn't do the trick.The dispenser still worked so we were buying bagged ice. The dispenser lever fell apart and my wife said fix them both or "I'm calling a repairman." My in-laws recently had a bad experience with an appliance repair service and my motto is that "if it's already broke I can't hurt it anymore" Found the Parts Select site and started reading everyone instructions. During the summer,our electricity had went off several times,so I figured that the icemaker control and motor assembly was the problem. Watched the installation video,and followed the instructions. Used parts diagrams and super glue to piece dispenser lever back together. Wife is happy and we saved $

replaced water valve and new icemaker.

Installed the icemaker control assembly this corrected the problem suspect contacts on the old unit were not making a good contact over time, due to the damp area in the freezer the new unit corrected the repair easy repair.

I had to order the module. It was easy to install. If i could have ordered just the gear and shaft, would have been a lot cheaper. Thanks for the addvise. Bill Paisley

Read on line that the motor module in the ice maker was likely to be the problem. I ordered the part and it came in as a complete module. All I had to do was to remove the cover, take out 3 philips screws, remove the old module and install the new one. I plugged it back in and had ice within the hour.

Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.

First I did the diagnostics and thought the water valve wasn't functioning so I replaced that, but it still didn't make ice. So I went on line and found the first thing to fix should have been the module and motor assembly. It was a real easy fix because I had pulled the ice maker before to investigate what was wrong. I just removed one screw and disconnected the electrical. There were four screws holding the motor assembly on. So I put the new motor on and had ice in 30 mnutes.