AMC7159TAB - Instructions

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

We got a a carbon steel but and drilled out the stews and put in regular screws. We also had trouble getting the cover back on and ended putting 2 more screws on the left side which had none. The installation was the easiest part of the installation.

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.

Placed in micro Great sevice. Thanks

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

Took the tray out of the padded box, and put tray in microwave. That easy, no tools required.

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.

OMG! I wish everything in life were so easy.....The cooking tray of our 15 year old microwave cracked and I swore it'd be impossible to find a replacement. That is until I discovered Partselect.com!!All I had to do was input the appliance brand and part I was looking for, and there is was. Thank you, Partselect.com!!

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the case back on reinstall it in the wall and voila...piece of cake.

I opened the microwave door to see if I might be able to do something. I removed the table and the turner was melted to the table so it all came off together. After finding partselect. Com on the web, they had the exact parts that I needed. I ordered the parts on 9/25/2012 and the parts arrived 9/27/2012 and I installed them and bingo! Everything worked. Thank you partselect!!!!