AGR6603SFS1 Maytag Range - Instructions

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

I first shut off gas to stove and unplugged the stove. I then opened the oven door and used a phillips screw driver to remove the three screws under the cover plate that sits behind the gas control knobs . I then removed the cover plate. I then took off the grates on stove top and proceeded to remove the two screws on each burner head with a phililps screwdriver. Some where tight so I used a drill driver on low speed to turn the screws out. After removing the burner heads I had to remove two screws on each corner in the front under the cook top of the stove to remove the cook top off the stove. But before that I had to release the two wires from a clip under the cook top for the ignitor switches before I could lift the cook top off the stove. These should be on the right hand side. Now I had access to remove the burner valve that had the broken stem that the knob is attached too. For this I used adjustable wrench to remove the nut for the gas tube that goes from the burner head to the control valve. Then I had to release the ignitor switch by pulling it off the control valve stem or gently pry it off with a flat head screw driver. Then used 1/4 in socket wrench to remove the top bolt to release the old burner valve off the gas plenum where all the burner valves are attached too. Then pull the old control valve off from underneath the gas plenum. Then i put in the new burner valve making sure it had a rubber seal around it where it goes up through the hole underneath the gas plenum. Then while holding control valve in place put the screw back in the top of the gas plenum through the other hole on top of the gas plenum and screw it in the burner valve making sure it also has a seal under the bottom of head of the bolt that you are screwing in to the control valve. This is so that no gas can leak from the plenum where the control valve is attached to. The control valve threads should be lined up with the bolt since both holes on the bottom and top of the gas rail (plenum) are lined up Use a 1/4 in socket to tighten down the bolt with the seal but don't over tighten. Then reattach the tube that goes from the burner head to the control valve with adjustable wrench and make sure not to over tighten. Then grab the stove cook top that you took off and replace it back on top of stove.After in place make sure to put those two wires back into clip that is under the cook top so wires are not touching the oven. You have to put part of your arm under the cook top and use your hand to try to push the wires back into the clip that's under the stove top. These wires will be on the right hand side. This is kinds tricky to do. Then tighten cook top back down with two screws and reattach the ignitor switch back through the valve stem of new control valve . It should clip in around the valve stem. Then reattach the cover plate over the valves stems with the remaining three screws and attach the control knobs.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!

ordered new broiler pan

Unscrewed old pan and screwed on new one.

Pop old one out and new one in

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

We needed a repair man to do the job because we did not have the tool to remove the screws on the burner heads. Also the on line diagram was not accurate. It actually was much simpler than showed in the diagram. Had we done the job, we would have done a lot of dismantling. The repair man removed the old top in a flash and the whole job took about 40 minutes. He knew what he was doing. Detailed instructions should come with the part so the do-it-yourselfer could figure out how to do the job.

very easy

Screwed in light bulb and glass protector

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes