AGR4433XDS2 Amana Range - Instructions

Unplugged 110 cord from outlet. Shut off gas supply. Removed rear cover (4) screws to access plug to ignitor. Removed boiler stove bottom drawer to access ignitor removed 2 machine screws 5/16 nut driver for ignitor replaced ignitor. I did no trouble shooting just took logical guess.

I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

This repair was easy as could be to screw take off the diffuser four screws in the back two little screws on the igniter

After I found the web site I looked at the possible solutions for my problem. My igniter was glowing so I was not sure that would fix the problem but several places indicated the igniter would fix the problem and after I replaced it the oven work great.

I didn't. Don't know how to get to light bulb to change it for this specific model

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

the hardest part was moving stove to trplace part

Very easy to replace.

I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then there was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

Replace two igniters that were not working. Did not fix the problem. Swapped wire positions from Spark Module and noted that the problem followed the igniter positions. Replaced Spark Module. Problem solved. Procedure required disconnecting a/c power, removing four screws, removing igniter wires from old module and reconnecting them to new module. Reinstalled new Spark Module in range. Reconnected a/c power. Test successful. Total time: 20 minutes.

Igniter is in the back bottom of the oven. I had to take off the top of the broiler compartment which has 3 screws. Unplugged the igniter which has two small screws and used a magnetic nut driver. installed the new one. It took 30-45 minutes.

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

I basically followed the video. The hardest part of the repair was trying to squeeze behind the oven to remove the back plate. Also the original screws holding the igniter took a small Allen wrench that I didn't have so I used an adjustable wrench. One screw was a little difficult but eventually got it tightened. Otherwise this was an easy repair like other reviewers have said.