Models > AGR4400ADW > Instructions

AGR4400ADW Amana Range - Instructions

All Instructions for the AGR4400ADW
76 - 90 of 215
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter on burner
Firmly grasp burner turn counter clockwise while lifting. Photograph the location of the wires. Remove with a Phillips head screwdriver. The igniter will lift and turn one quarter turn then pull through bottom. Reverse the steps to install the new igniter. Test knew igniter. Put tools away
Parts Used:
Oven Igniter - Vertical Mount Bake and Broil Top Burner Igniter
  • daniel from MENIFEE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not maintain temperature and not heat up correctly
Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.
Parts Used:
Oven Igniter - Vertical Mount Bake and Broil
  • Kevin from EDGEWOOD, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler wouldn't turn on(ignite)
Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.
Parts Used:
Oven Igniter - Vertical Mount Bake and Broil
  • James from FLORISSANT, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't light.
It's happened before and the igniter has always been the problem. This time, however, the mounting holes were slightly off and had to be drilled out. The connector didn't mate up and so both had to be cut off, the wire stripped back and wire nuts used to make the connection. In the end, it all worked out. I guess since its kind of old, you can't stock every component for every oven. Oven works perfectly now.
Parts Used:
Oven Igniter - Vertical Mount Bake and Broil
  • Andy from NEDERLAND, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
Oven Floor Panel
  • Tara from ALBANY, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks were old
Replace the racks. No special instructions.
Parts Used:
Oven Rack
  • Sandra M from DISTRICT HTS, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electrode broken on end and would not ignite the burner
It was a very easy repair. I just connected the two wires to the bottom of the electrode and set the burner on stove top and turned it to the right to lock in place. Turned burner knob on and burner worked great.
Parts Used:
Burner with Electrode
  • Michael from SAN PEDRO, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner igniter problem.
Replaced with a new one.
Parts Used:
Burner Head Cap with Spark Electrode
  • Dhirajlal from SKOKIE, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The igniter of the burner was worn out of constant use.
First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.
Parts Used:
Top Burner Igniter
  • Israel from HYATTSVILLE, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Parts Used:
Door Seal
  • Mary from WINCHESTER, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Parts Used:
LEVELER-FOOT,SCREW,F/S,NYLON
  • Phyllis from BROWNVILLE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Parts Used:
Door Seal
  • Anita from ELKTON, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back burner would not light
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.
Parts Used:
Top Burner Igniter
  • Christopher from WOODBURN, OR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Parts Used:
Door Seal
  • Mz from COLUMBIA, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Parts Used:
Oven Rack
  • Linda from BURBANK, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the AGR4400ADW
76 - 90 of 215
Back to Top