AGM339 Amana Dryer - Instructions

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

First I shut off the gas supply (the valve is an in-line shut-off and it's right there. I removed both of the retaining screws and detached the gas supply line.

Remove hte valve from the mounting plate (two more screws) and then reversed the process to replace the part.

It works just fine, thank you very much!!

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new

The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.

Checked ignitor it was working ok, disconnected 3 pronged coil and disconnected 2 pronged coil using multi tester checked continuity on both coils both tested 0,with help of operator ordered M Series new style coil kit. When parts arrived installed coils attached wire harnesses installed bracket and 2 screws that secures coils. Started dryer it worked and stayed working who needs the Maytag Repair Man probably saved about 200.00 between service call and markup on coils. Thanks Virtual Repairman

I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

i removed the door and front panel then removed the two screws holding the coil bracket,disconnected the two wires on coils,set new coils in place and reversed the above process

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.

Installed new coil, helped but have other issues that I'm troubleshooting.