AFB2534DEQ Amana Refrigerator - Instructions

This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

My son (who does HVAC, but not appliance repair) did some investigating by taking front and back panels off and determined that the evaporator coil was freezing over because the defrost wire was not heating up. He and his girlfriend did some real-time internet searching for diagnostic info because NO control diagram was included with the refrigerator. He determined the problem was most likely the electronic control board. Ordered and installed a new board and the refrigerator is back to working fine. Took about 2 hours to diagnose the problem and 1/4 hour to actually install the control board. Kind of disappointing that this control board failed when the refrigerator was less that 4 years old.

After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.

Followed the video and installed the new Jazz board. The board cam in 1 piece which had to be separated into two pieces, but the scored area on the board made it less intimidating. At the same time I replaced the two incandescent lamps in the refrigerator area with LED lamps. Getting the housing for the control board apart was the most difficult part, installing the replacement board was a breeze.

You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Info on your site allowed me to determine the most likely cause of the problem, defrost thermostat, and that fixed it. Good installation instructions on the site too. Part was super easy to install. Hardest part was removing the snap-in/screwed-in plastic parts that held the sliding baskets and back panel in place. Didn't break any.....Thank You!

We came home from a long vacation to discover a warm refrigerator with its contents in various stages of decay.

Turning the freezer thermostat to its warmest setting then back to cold generated clicks, and after a few tries the compressor started and cooled the refrigerator to its normal cold temperatures. But… later the compressor again failed to start, and everything warmed back up again. With persistence and turning the thermostat up and down several times a day, we could keep the fridge cold.

It was time to order parts. We needed a new start relay and capacitor for the compressor. For our Amana ARB2214CW a start relay (WP12555902) and capacitor (WP65889-4) were listed on the first page of the Partselect parts list for my refrigerator. I ordered them, received them, removed the old capacitor and start relay (which rattled when shaken). and prepared to install my new parts. The new start relay did not match the old. The old start relay fit my wiring which had a single plug with two small female spade connectors in the plug. The new start relay required wiring with two separate female spade connectors; one the normal size and one larger. Phone calls to Partselect and to Westinghouse shed no light on the discrepancy. On the second page of the Partselect parts list was a combination of a start relay and a capacitor (W10613606) that matched my electrical connector. I could see the connection in the photograph. I ordered it and it fit. Easy peazy. That fixed the compressor start problem. Every time the freezer thermostat clicked on, the compressor started. Success.

But… from our troubleshooting we now had a thermometer the freezer, and it was obvious that the temperature difference between the cold point where the thermostat turned the compressor off and the warm point where the thermostat restarted the compressor was much too wide. In addition, the knob was hard to turn and was sticky as it turned. Oiling it fixed the sticky knob problem but not the wide temperature difference problem. I ordered a new freezer thermostat (WP67003000), received it, installed it, and all is now fine with my refrigerator. The new thermostat was physically a little different from the original, but it fit and worked.

I returned the first compressor start relay and capacitor and received a refund including the shipping charge.

The vents at the back of the freezer were constantly getting packed with ice. A repairman failed to spot the problem. I used Partselect's web site to do my own analysis and determined that it was the defrost thermostat.
I followed the web site's instructions, which were exceptionally good. Behind the rear wall of the freezer was a lot of ice on the cooling fins and heavily encrusted over the old thermostat. (It was not really difficult, but I am in my 70s and no longer do things like this on my own.)
After replacing the part, I checked the ohms of the old part and found it to be faulty. Since then, the refrigerator has been working great. I wish I had started here. The repairman I had hired replaced the "control board" at significant expense. I doubt very much that anything was wrong with the old control board.
Many thanks to Partselect for an exceptionally helpful web site.

The video was a great help. I was able to replace gaskets on both doors with out taking them off and no tools were needed.
One of the refrigerator doors has a plate that closes with the door that makes replacing the gasket questionable but I was able to do it with no problem.

CHECK DEFROST THERMOSTAT WITH VOLT OHM METER AND FOUND THERMOSTAT BAD ALSO OHMED OUT HEATER AND HEATER CHECKED OK INSTALLED HEAT SRINK CONNECTORS ON NEW DEFROST THERMOSTAT PUT SYSTEM BACK INTO O
PRATION ALSO CHANGED WATER FILTER ON REFERGRATOR
SYSTEM WORKING OK AND NO ICING OF COILS THANKS WADE BOYLES