AFB2234WEW0 Amana Refrigerator - Instructions

Your service is wonderful! I found the part on my mobile phone with a very quick and simple search, then I called in to order. The ordering process took less than 3 minutes, and I had my new shelf in three days. I dreaded ordering, because I just knew that the replacement shelf would be super expensive, but the whole thing cost much less than I expected--less than a dinner out. Thank you so much for your efficient and friendly service!

followed the instructions provided and that's it!

You need to lift up the glass part and simply fit it the center rail in, very simple

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

The other instructions and the video provided by Parts Direct are pretty good with instructions, but they omit two steps. First, if you have an ice maker, you will need to unplug the connector on the back side of the panel you remove at the back of the refrigerator to access the drain tube. Just unplug it and you can move the removed panel to the side without disconnecting any of the water lines. Second, the instructions say to just reconnect the "bottom end" of the new p-trap drain to the drain pan at the bottom of the refrigerator. They don't tell you there are two places to connect the new p-trap to the drain pan. The original tube/trough connected to the one at the back of the drain pan on the left (viewed from the rear of the refrigerator). At first, it looks like the new p-trap won't reach to it for the connection, but if you look closer, there is another connector to the right of the original one that the p-trap connects to properly. Replacing the drain trough with the new p-trap was actually pretty easy and would only take about a half hour. Add another half hour to give the refrigerator coils a good cleaning as they will need it now that you can reach them. The real time consumer, 3 to 4 hours, is needed to use a hair dryer to melt and clear the ice from the condenser at the back of the freezer so the water can drain. Just take your time and all the ice will eventually melt and drain out so the new p-trap will work properly.

No instructions came with the parts, however, on the website where we ordered the parts was a video that walked you through every step. We followed the video and had the repair done in no time.

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

Watched installation Video on the website parts. I put the new gaskets in bath tube in warm water for a few minuets until the gaskets were warm and pliable. I removed old gaskets cleaned door facing and installed new gaskets as instructed on video. Thanks for the information on how to install because I was dreading trying to do this task. "Just follow and listen to the instruction on Video".

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

Removed the middle screw and the whole rail came of. Unplugged wires and removed old rail. Plugged in the new rail and slid top and bottom slides on and put on the middle screw. Job finished

Repair was a piece of cake. My only wish would have been a little more informed on a few other parts I could have replaced as well. It obviously would have increased my cost, but would have simplified the install process, and still would have been cheaper then calling a service guide. I would recommend buying and installing the new gaskets when doing this. And possibly the steel support bar that goes threw the plastic shelf. Removing that bar was the most difficult task, difficult only that if you used to much force, SNAP!! and then your pissed! and have to start all over.

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

The digital display numbers (0= off and 7=coldest setting) controlled by the ECB would continually be replaced by straight lines, and the refrigerator would stop cooling. I tried unplugging it for a while. After plugging it in again, it worked (the digital display came on, I set it to "4" and it reached the proper temp), but the problem occurred again the following day, and then it stopped cooling entirely. I ordered the ECB, and it arrived in 3 business days. I watched the installation instruction video, took my time, double-checked the vid a few times to make sure I was doing it correctly, and replaced the ECB by myself in less than an hour. The refrigerator has been running without problems for 3 weeks now. My fridge had a different light bulb configuration than the one in the video, but everything else was the same, and it was a simple repair.

I ordered a right & left gasket but when they arrived there was no indication of which was the right or left one...so I just had to guess...I easily lifted the old gasket away from the door & removed. Then starting at the top began inserting the portion that goes into the groove with the help of the table knife, continuing down both sides..then sat on a stool to push the bottom section into place...Had to go back over several areas to reseat but finally closed the door to hopefully set the gasket..Drank some hot tea, then removed the left gasket & began the process all over...The extra flaps ended up on the left side of the door so I may have to remove this side and reposition...I'll check it in a few..then will blow all with a warm setting of the low dryer to continue helping the molding process..

I replaced the control board first. The freezer back panel frosted up and the refrigerator warmed up again. Then I force (short option vs long) defrosted the refrigerator. However, a few days later the defrost issue came back again. Force defrost no longer worked, though likely due to a severe ice build up behind the freezer panel. I ordered the wire harness. I took off the freezer door (loosen four screws only), removed the tray rails, ice maker, thermostat housing and vent mounted on the freezer panel. The rails and the vent are a bit tricky to remove since no directions exist. I then removed the fan above the coils and then removed the wire harness. Installing the new harness is easy except that I had to modify one of the ground connections for it to mount properly. I tested the unit for 72 hours. The defrost cycle eventually kicked in (dripping onto a pan and sizzling sound). I then reinstalled all parts. No frost build up. Good to go!