All Installation Instructions for Amana Range AER5515QAW

my first order a small drip bowl

came only I had to order the set again

Parts Used:

Drip Bowl Kit - Light Gray

marie from WATERBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken Inner Glass Pane

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Parts Used:

Inner Door Glass Pane

Joseph from Lewiston, ID
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

F5 fault code kept appearing

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Parts Used:

Long Oven Sensor

Louis Rodriguez from Granbury, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Jennair cooktop with coils lost one of its coil guides.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Parts Used:

Surface Burner Receptacle Kit

Bruce from SOUTHBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner plugs were loose

used the supplied parts...very easy. The parts were exact replacements.

Parts Used:

Surface Burner Receptacle Kit

James from CONCORD, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven not heating to desired temp

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Parts Used:

Long Oven Sensor

Raymond from Ridgecrest, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

We Heard A Pop Saw A Flash And The Bottom Element Didn't Work

The first time is always the hardest. I took out the bottom cover that had 2 screws saw the broken element took out 3 screws to the emement. I then pulled out the stove unpluged it from the wall and took off the back panels several screws and found the element connected to the wires I marked the wires left & right and disconected them. I reversed proceedure to install the new element. The oven still won't go over 250 degrees I think when the element blew it to the circuit board with it.

Parts Used:

Oven Bake Element

Norman from Brockton, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Parts Used:

Long Oven Sensor

Ralph from Nicholasville, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Parts Used:

Long Oven Sensor

Philip from Winter Haven, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed to replace over door gasket

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Parts Used:

Door Gasket

Genie from Conshohocken, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The three braces under the coils had weakened and fallen apart

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

Parts Used:

Surface Element - 6 Inch

Suzanne from COZAD, NE
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Front glass broke

Unscrewed bottom piece; put on tape and new glass; re-installed bottom.

Parts Used:

Range Double Sided Tape

Dean from Bethpage, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake Element burn out

Can of Corn fix! Remove the two screws in the element cover plate (they're in the back- left/right corners). Remove the two screws that hold the element in place. Pull out the two prong ends of the plug in portion and hold the black / white leads so they do not fall back in behind the unit. Plug in new element (it only goes one way). Screw everything in and test. Place cover plate on after test. Like I said ... a "Can of Corn" fix!

Parts Used:

Oven Bake Element

Bob from Oroville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Terminal block arc'ed because a wire had become loose.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Parts Used: