AER5511AAW Amana Range - Instructions

First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall
(would only come out about a foot and a half due to the gas line connection). Removed the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.

First I removed the two screws on the bottom heating element that hold the element in palace,one on the left side one on the right side, I then pulled the element out about 2 to 3 inches and disconnected the two wires. I then installed the new element. It took me about 20 mins. The cost of having some come out to fix this was about ten times of what I paid for this part. Thanks for the quick service.

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

Removed the oven door and oven racks. Turned off the power to the range/oven. Unscrewed the bottom element and place the new element in its place. Screwed element in and replaced the oven door and racks. Turned the power back on and turned the oven on. It works great.

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order

I actually had to hire someone to fix the problem. My stove happened to be one of those they describe on the internet where the wires were not long enough to pull out. Had I tried it would have become a major repair job. The repairman had to use needle nose pliers to grab ahold of the wires and get them out far enough. All went well though and he only charged $25.00.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

Took the old levelling leg out and screw the new one in.

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.