AEQB7000EP0 Frigidaire Dryer - Instructions

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.

UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.

Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now

After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.

remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in

The how to video was great. I had a little problem with getting the belt back on the pulleys. Not enough room for my hands. I did manage to get it back on ,and runs great

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

Unplugged dryer. Removed top panel (2 screws top back of dryer). Removed control panel ( Unplugged from control board and 2 screws) Removed front panel with door ( Unplugged light from control board, door switch at connector, and 4 screws) Removed Control Thermister from dryer exhaust blower housing located bottom front of dryer ( Unplugged 2 wires and removed 2 screws ) Installed new Control Thermister and replaced all screws and panels in reverse order. Note: Noticed connector for door switch seemed a little loose when connected correctly. Used electrical tape to reinforce connection. Plugged dryer back in and checked operation. Dryer has been used approximately 10 times since repair with no issues.

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Ordered in new Element. (took apart dryer first and verified the coil on the old element was broken).

-Disconnected power
-Used flat blade screw driver and popped the top of the dryer off (two clips at front of the dryer on the door piece). Pull lid back and it will rest on its own.
-Removed two screws on the inside of the front door panel then used flat blade to pop four clips off. Lift up then out to removed door panel, drum will fall down.
-Removed small white plastic rest from front frame.
-Removed back silver vent to access motor. Pull the belt tensor away from assembly and pull belt out.
-Remove drum by grabbing belt and front of drum and forcing it up until it releases from the ball housing. Slide drum out of the front of frame/dryer.
-From here you can see the heating element. disconnect the coil wires (pull them). These are in series so it doesn't matter how they go back on. Disconnect the thermostat wires (X is negative lead).
-Removed the four screws from the back of the dryer to disengaged the element. Removed.
-Reassemble backwards.

Remove rear control panel cover and remove drum belt from pulleys. remove top cover by pushing in on the 2 hold down fasteners on the front with flat head srewdriver. remove front panel by removing the 2 screws and then pop it out by lifting up. disconnect the wires at the quick connect plugs and set the front aside. lift the drum up to pop it out of the bearing housing and move forward slightly to give youself good access to the wires for the heating element and disconnect the 2 wires. remove drum the reset of the way out and do your work. Replacing the heating pan and drum bearing is pretty obvious what to do. (just a few screws). remove thermal cutoff switch from old pan and install on new pan. reinstall in reverse. no need to label wires because it doesn't matter where the wires go an a switch (justs makes and breaks a circuit) and the heater doesn't matter as long as both wires are hooked up to complete the circuit. You can't mess up the quick connectors on the door. Only my heater failed but I also replaced the drum bearing as long as I had it all apart (only another ~$20). Take the time to clean out the dust from inside the dryer, it will help the blower motor run cleaner and cooler and last longer. I bought a belt also to have on hand for replacement. I didn't replace it since my old one was good and it is real quick to replace at a later time.

replaced bearing and shaft new belt and everything works just fine