AE5213 Dryer - Instructions

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.

p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days

Thanks
JoAnn

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

Followed video on PartsSelect website, they made it real easy.

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

Popped in the new part. Really! That easy!

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

as described in video. Very well done. Thank you

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.