AE5113 Dryer - Instructions

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

removed old element, relaced with new element , thermostat dryer works better than it has in along time

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.

removed front of dryer, replaced old pully and put on new belt.

Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

First I unplugged the dryer and turned off the gas. Pryed up the top of the dryer at the front corners to free the front panel. Removed the two screws at the bottom front of the front panel. Then disconnected the three electrical connections for the door button. Put the front panel to the side. Then took out lint tray and then removed four screws that hold the lint blower piece and put it aside. Then I could see the motor and the idler assembly is on the back of it. If you have a camera take a picture of how the belt is on the pulley. If not you can draw a general idea of the direction. I reached back and slipped the belt off the idler pulley. Removed two screws from the front bottom of motor fork .Removed two screws from a small electrical hook up thats on the front of the motor and removed it. At this point I could just slide the motor out. With a rachet and a regular wrench I removed the small bolt holding the arm on. Put on the new arm. Slid the motor back in and reconnected the belt. Put everything back together in the same way. Yeah it works. I am a 58 year old woman and this job required no brute strength. Don't be intimidated its really not that difficult to fix it yourself.

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

replaced idler puller and washers