ADE4BRGS171TW01 Speed Queen Dryer - Instructions

when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

Unplug. Remove door and front panel. Unplug two coils. Remove one screw and loosen other on bracket holding coils in place. Slide off coils and replace ( take note one has terminals up and one down). Reassemble.

First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!

After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of going to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!

Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.

Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You

1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valve opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012

open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.

Checked heating element and it glowed so I replaced the ceramic gas valve regulators. 4 screws to take front off the dryer and 2 screws to replace part. Couldn't have been easier but I wouldn't have been able to do it without watching the video first.

Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.

Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying close attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.

Unplug the Dryer; remove the lower exterior cover and white plastic drum vent with nut drivers. These two fuses will be setting on top of the function board in front of the gas heating tube.
With a short screwdriver, remove the fuse cover/holder, lift fuse and unplug, replace, re-plug, screw back the cover/holder and you’re done.
Reverse your initial actions...