ADE4BFGS171TW01 Speed Queen Dryer - Instructions

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

Checked the resistor to confirm it was good. Removed the two screws that are accessible after you pull the lint screen out. Use puddy knife to release the two plastic clips that hold the top on. The top will pop up like car hood. You have to pull up on it with steady pressure. I used a plastic puddy knife to prevent scratching anything. Prop top up so it does not fall back down and strike your head or fingers. On each side inside the housing there is a sheet metal screw that holds the front of the dryer on. Before you remove them unplug the door switch wire. As you get these off you will notice that the whole front is loose and the drum looks like it will fall out. It may if you mess with it. Gently tip the front away from the dryer housing and drum assembly. After the front is out about 5 inches pull up and the bottom can be moved away out of the small hook clips. Set it aside. The burner assembly is on the lower left. The coils are there remove the sheet metal screws and lift it up. Remove them one at a time. Notice the small locate pin and position the coil in the same orientation assemble in reverse. The door is tricky to get back on. Don't forget to unplug before doing any work. This can be done without disconnecting the gas service.

Unplug electric, open top, take off front, with a small Phillips screw driver remove two screws securing the coils, remove one coil at a time, unplug and replace with new coil, secure with metal bracket and reinstall front and top and your done.

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Undo 2 screws take units out, clean a little, install new parts and screw down, done, great site !!!!!

All went very easily

unscrewed the 2 screws holding the coil's in place took wires off one coil at a time tested coils with ohm meter found the two wire coil was bad replaced and scered the bracket that holds the coils back in place.PartSelect gave me a list of what was causing the problem and what the % of what was the cause,this helped alot Thankyou PartSelect

I'm a 65-year-old woman with no prior appliance repair experience. I learned on the web that 30% of the time, the failure-to-heat problem is caused by the valve coil, and 30% of the time, it's the cycling thermostat. So I ordered both parts. I watched installation videos on the web. The valve coil was accessable through a front port on the dryer so I started there. I had to go buy a stubby screwdriver because access to the screws was limited. From there, it was easy to take out the old valve coil and install the new one. Just 5 minutes. I plugged in the dryer again, turned it on, and it worked.

First I opened the front of my dryer panel to see when the dryer was on if there was any gas flowing. I found that the ignitor was glowing , but no gas was releasing from the valve. So I figured that that is the root of the problem. I changed the old gas valves and replaced them with the new ones. It worked!! The whole process didn't take more than 30 minutes.

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.

Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying close attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.

Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself.

Removed 2 screws at the lint filter, unplugged dryer, next I popped the top off with a standard screw driver lifted the top all the way up and secured it from falling back down, used a 5/16" nut driver to remove the top 2 screws holding the face on, disconnected the door switch, pulled the face panel off and set it aside, then I removed the tension pulley on the bottom and took the drum out, unscrewed 2 screws holding the coils removed the old coils and installed the new reconnected the leads to them, vacuumed out the cabinet and motor, inspected all moving parts for wear, including the belt, reinstalled every thing in reverse order, had job complete and ready for clothes in 9 mins, it helps to have your son/daughter hold the drum against the back wall while reconnecting the tensioner and belt.

Removed front panel unscrewed the 2 screws on the coil cover. The coil with two prongs had to upside down 3 the prong coil right side up that only way the cove will fit, plug them in re attach the cover and your done