ADE3LRGS171TW01 Speed Queen Dryer - Instructions

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

Removed the two screws fromt he lint track on the top of the dryer. Inserted putty knife between the top of the fromt panel and the dryer top and pushed in to release the two catches for the front panel. I rested the top panel against the wall to get it out of the way of the front panel . Next I removed the two nuts at the top of the front panel . Removed the electrical safety connector for the door using a very small screwdriver to release the catch. Pull up on the front panel to detach it from the bottom catches. I rested the drum on a couple of 2x4s to support it while the front panel was off. Locate the housing for the coils which is on the front of the dryer left side. Remove the cover fromt he coil housing by using a stubby phillips screwdriver and remove the top two screws. Remove the wiring connectors from each of the coils. Replace the coils being careful to align the coils with the "keys" in the housing cover. Reverse the process to complete the job taking care to ensure the felt around the drum does not bind.

Checked the resistor to confirm it was good. Removed the two screws that are accessible after you pull the lint screen out. Use puddy knife to release the two plastic clips that hold the top on. The top will pop up like car hood. You have to pull up on it with steady pressure. I used a plastic puddy knife to prevent scratching anything. Prop top up so it does not fall back down and strike your head or fingers. On each side inside the housing there is a sheet metal screw that holds the front of the dryer on. Before you remove them unplug the door switch wire. As you get these off you will notice that the whole front is loose and the drum looks like it will fall out. It may if you mess with it. Gently tip the front away from the dryer housing and drum assembly. After the front is out about 5 inches pull up and the bottom can be moved away out of the small hook clips. Set it aside. The burner assembly is on the lower left. The coils are there remove the sheet metal screws and lift it up. Remove them one at a time. Notice the small locate pin and position the coil in the same orientation assemble in reverse. The door is tricky to get back on. Don't forget to unplug before doing any work. This can be done without disconnecting the gas service.

Unplug electric, open top, take off front, with a small Phillips screw driver remove two screws securing the coils, remove one coil at a time, unplug and replace with new coil, secure with metal bracket and reinstall front and top and your done.

The dual cil gas valves were out of resistance range. The new coils were easy to install with a screw driver, sockets set and multi-meter.I checked the coil resistance and one of the new coils were a little high, but I installed them and they have been working fine.

I went onto the Part Select website, they have a problem solving section that told me the most likely part to replace first and a description of the machine and the location of the part. I purchased the part, I unplugged the electric cord first. I then opened up the front of the machine with a philips screw driver, changed the part with the philips scew driver, I put back the front of the machine and the machine worked. It doesn't get any better then that!

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

Need a short handled phillips screwdriver. Unplug dryer from socket. Remove two screws near the bottom of the front panel. Swing the panel to one side so electrical wire doesn't need disconnection. Remove two screws holding bracket over the two coils. Unplug both coils. Plug in new coils. Replace bracket. Replace front panel. Plug machine back into electrical socket. Problem solved.

I got great advice and the know how form other's instructions. It was a really easy fix. I unplugged the dryer and turned off the gas valve. Open up the dryer by taking out the two screws securing the lint screen. Then pop off the top of the dryer by inserting a screwdriver. Disconnect the door switch and depending on model remove the two screws or bolts that keep the front panel attached. Careful, on my dryer once took the front panel off the drum fell forward. I kept it in place by wedging a small cardboard box under it. Unplug the two wires going into each of the coils. Remember which one goes where(2 prong vs 3 prong). Undue the two screws holding the bracket to the coils and remove bracket and bad coils. Put the new coils in, attach wires and bracket. Put dryer back together. Make sure to remember to plug back in door switch. I forgot and when I tried to test it wouldn't work and it got me worried that I broke it or something.

Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.