ADE30RGS171TW01 Speed Queen Dryer - Instructions

Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.

Pulled out AC cord from wall socket first! Removed the dryer door and front panel (2 screws each) Then pulled both wire connectors off 2 coils. Removed hold -down bracket over coils. Replaced both coils and reconnect . No need to replace electronic igniter for gas. The right parts were shipped faster than I expected. Easy job. The Maytag repairman remained unemployed once again!

Undo 2 screws take units out, clean a little, install new parts and screw down, done, great site !!!!!

Pried the top up, disconnected the door switch, removed two top screws holding the front panel, disconnected the spring and removed the front panel. Removed the screws and retainer holding the coils, replaced both coils and reversed the process. This was the third component I replaced to solve the problem....a cheap multi-meter and some testing would have solved the problem sooner. We now have the whole heat cycle.

The repair went very smooth. I was able to follow the directions on partselect and had the repair done in 15 minutes. I took extra time to test the continuity on the ignitor and fuses. I also used the shop vac to clean out the inside of the dryer. The best part I liked about this web-site is the fact that once I described the problem I was told that the "M" series style coil was the fix 90% of the time! $27.70 including shipping was all it cost to make my clothes dryer work like it did the first day we got it!!

Wouldn't have had a clue how to gain access to the coils without online instructions. It actually took longer to open the front of the unit than it did to replace the parts. Following the online instructions I removed two screws under the lint trap door. I then used a stiff putty knife under the left and right front corners of the lid to release the top, which I tilted back. Per the instructions I easily located the two screws releasing the front of the dryer. You have to lift the drum a bit to release the front panel. Once removed I was able to remove and replace the failing coils and then reversing the steps to put it all back together. An easy job and the dryer is back in shape.

All went very easily

unscrewed the 2 screws holding the coil's in place took wires off one coil at a time tested coils with ohm meter found the two wire coil was bad replaced and scered the bracket that holds the coils back in place.PartSelect gave me a list of what was causing the problem and what the % of what was the cause,this helped alot Thankyou PartSelect

I'm a 65-year-old woman with no prior appliance repair experience. I learned on the web that 30% of the time, the failure-to-heat problem is caused by the valve coil, and 30% of the time, it's the cycling thermostat. So I ordered both parts. I watched installation videos on the web. The valve coil was accessable through a front port on the dryer so I started there. I had to go buy a stubby screwdriver because access to the screws was limited. From there, it was easy to take out the old valve coil and install the new one. Just 5 minutes. I plugged in the dryer again, turned it on, and it worked.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

First I opened the front of my dryer panel to see when the dryer was on if there was any gas flowing. I found that the ignitor was glowing , but no gas was releasing from the valve. So I figured that that is the root of the problem. I changed the old gas valves and replaced them with the new ones. It worked!! The whole process didn't take more than 30 minutes.

I first replaced the temperature sensor. That did not help and when doing investigation when thr drier was warm I found the vallve would open and close if I touched the coils

Repair itself was not hard, Pop top, unscrew front panel and pull forward to get at the coils under the drum. --THIS IS THE KEY POINT i ENCOUNTERED: I tested the coils and the resistance was right according to the schematic. But still the flame would go out after while. --on a whim I pulled the front cover and tested the coils immediately after the flam wouldn't re-light.---When the coil got warm, it would open (no continuity). When it cooled down again the correct continuity would return. Replaced the coil and no more problem

follow Steve the repairman's instructions they were very good

I started with the process of elimination, based on the web site part failure percentage...so I started with the cycling thermostat and thermal fuse, without success. Next, I placed an order for the 'M' Series New Style Coil Kit Part # PS334310. Which, are located behind the lower front panel