ACS7270AS Amana Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

It was real easy. Removed two screws, pulled the element forward, removed to clip on wires, removed element and put the new element in place, replaced wires and screws, turned it on and up to temp. in no time. great service and quick delivery on getting the part.

replaced element

removed the screws disconnected the old one and connected the new one and put the screws back on it

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

I went online to learn what F-3 meant and it said temp sensor malfunction. I ordered the part - it looked the same so I repaced the old one and then the plugs were different. I cut the plug off the old sensor and cobbled together a connection. I powered up the stove and the burners were ok, but the oven appeared dead. about an hour later the alarm went off and it displayed F-1. I figured I needed to order another part, but hit Oven cancel and the display lighted up. I set the clock, heated to 400 and made a tray of cornbread. It seems to work ok, but I need to make a better arrangement. perhaps cut the new part connector off and splice the old connector. I don't like having electrical tape so close to the oven - it will probably melt with much usage. It is working - for now!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

First, I turned off the power to the house at the breaker box. Then I removed the broken heating element through the front oven door. I hoped this would work as it seemed from other reviews that some people pulled the oven out removed the back panel in order to access the element. I unscrewed the plate and then gently pulled the element out. I had a little trouble "unplugging" the element. When I tried pulling, it seemed they were stuck tight. Turns out you have to sort of jiggle the connectors and then they easily pull apart. Had I figured this out initially, the repair would have been under 15 minutes. Attaching the new element to the connectors, rethreading the wiring back into the holes, and then rescrewing on the back plate too the oven wall took just minutes. Easy peasy. So glad I spent $40 to fix rather then $500+ for a new oven!

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.

Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I installed everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.

my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.