ACS4250AW Amana Range - Instructions

The repairman that had come had stated that this part is no longer made, but I was able to locate one through PartSelect and was able to replace it with minimal effort.

I removed the three screws that held down the stove glass top surface and had a person hold the stove top up while I removed the two screws which held the autolatch assembly in place. I then swapped the leads from the failed assembly to the new one and replaced the screws which were removed. New assembly tested out fine and oven was able to self-clean again.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.

I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and removed the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and was about to disconnect the two wires. It was a bit hard to pull out the wires by hand, but I got some WD-40 and pliers and it was easy. Hooked up and replaced and voila. It was done. Saved me a new $1,500 stove. I wish I knew that the lamp only needed to be unscrewed and not the whole unit replaced.

Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased