ACR4303MMS2 Amana Range - Instructions

David from Saranac Lake, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Parts Used:

Oven Sensor

Dave from Titusville, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The burner didn't work because it had the wrong drip bowl

Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.

Parts Used:

Leslie from Spring HIll, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Old receptacle was burnt from lots of use.

Just cut the old receptacle wires and splice in new kit. Very simple and worked perfectly.

Parts Used:

Range Receptacle Kit

Brenda from Scurry, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Burner would go on and then turn off, repeatedly.

Unplugged unit, removed plate behind control panel, removed 5 or 6 wire connectors, pulled off burner switch knob and removed 2 screws that holds switch in place. Reversed the procedure and was done.

Parts Used:

Robert from Tonawanda, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Wrong replacement Drip Pans installed previously caused damge to 8" Burner.

Removed burners and drip pans, replaced drip pans and re-installed burners. Simple....

Parts Used:

Lloyd from Pinellas Park, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Generic Drip Bowls Made The Burners Tilt.

Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.

Parts Used:

PATRICIA*NAYLOR from NEW PRT RCHY, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

the dial would not work unless the special screws, which are extra short, are utilized.

since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.

Parts Used:

Bruce E from Oxford, MS
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

could not control temp on burner

Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!

Parts Used:

Ernie from Cameron, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

The large burner sometimes stayed on high too long, burning food

My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!

Parts Used:

Harry from Seminole, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Old Drip Bowls

Lifted out the old ones and inserted the new ones and my range top looks brand new now!

Parts Used:

James from Edgewater, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

none

I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.

Parts Used: