All Installation Instructions for Whirlpool Range ACR4303MFW5

Drawer guides missingJust

Just follow included instructions.

Parts Used:

Drawer Glide Kit - Black

Mark from Killbuck, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Receptacle Assembly Has Burned Out

Remove old receptacle and connected and replace new one. Burner now works perfectly again.

Parts Used:

Range Receptacle Kit

ANN from MANITOWOC, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Paint peeling from strip

removed 3 screws holding the strip and replaced with new strip

Parts Used:

Range Trim Lower (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Replaced screw

By hand screwdriver

Parts Used:

Range Screw

Screw

Judith from SALEM, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner would stay on when switch set to low heat

Unplug and pull out range.
Unscrew the back of the range with Phillips #2.
Unplug wiring harness from switch.
Unscrew the switch from the front of the range with P2 driver.
Install and plug in new switch.
Remove the spring steel knob retainer from shaft.
Cut off extra knob shaft with dremel to match others (there is a narrow segment at the proper length).
Reinstall knob retainer, knob, and range panels.

Parts Used:

Surface Burner Element Switch, Large Burner

Casey from WARBA, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven not reaching temperature

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Parts Used:

Oven Sensor

Marsha from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

It was a rather simple fix--just replacing burner pans

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Vicki from Jefferson, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

could not control the temp of the element

take off back panel, simply unplug the old switch and plug in the new one. Simple

Parts Used:

Infinite Switch - 6 Inch

Steve from GREENBRIER, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

chemical etching of black painted finish on drawer front panel

took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!

Parts Used: