All Installation Instructions for Maytag Range ACR4303MFW2

Bottom Door Trim Rusting

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Parts Used:

Range Trim Lower (White)

Dennis from Grimsley, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

The Parts Came With No Instructions And We Couldn't Find Directions On Line.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Parts Used:

Side Trim

Side Trim - Right Hand Side

Kathleen from Livingston, MT
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

Was this instruction helpful to you?

Drawer Glide Snapped Off And Broke

Snapped in the new drawer glide. Took less than 5 minutes.

Parts Used:

Drawer Glide Kit - Black

PATRICIA from GEORGETOWN, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Heating element would not get red hot

Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.

Parts Used:

Infinite Control Switch, 6"

James from Lewisville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

rusted drip bowl

remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.

Parts Used:

Drip Bowl - 8 Inch

kyle from Schwenksville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Two drip Bowls needed to be replaced

No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Robin from Boca Raton, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip Bowl beyond cleaning

Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Ann from Memphis, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Parts Used:

Range Terminal Block

Robin from Vanderbilt, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

corroded, rusted drip bowls

replace

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Noah from Richardson, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Left front 8 inch burner knob control stop regulating heat temprature.

I purchased a new infinite control switch 6". and replace the old one.

Parts Used:

Infinite Control Switch, 6"

Alfred from Ann Arbor, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Wrong replacement Drip Pans installed previously caused damge to 8" Burner.

Removed burners and drip pans, replaced drip pans and re-installed burners. Simple....

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Lloyd from Pinellas Park, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

No Problem

Needed new drip pans for range top. Easy fix. Was impressed on how quick the parts were shipped out to me.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Sharon from Emmett, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old drip bowls, tried prepackaged from box stores

After putting up with ill fitting generic versions of our drip bowls, we smartend up and ordered correct parts. They went in super easy, perfect fit and the heating element is now perfectly level. Who knew that following the manufactors recommendations to buy correct parts would make such a difference? Well we know now! Thank you. The parts were shipped almost immediately and delivered as promised.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch