ACR4203MNS0 Amana Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bowls had burnt on food
-
David from Saranac Lake, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
rusted drip bowl
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Parts Used:
-
kyle from Schwenksville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner would go on and then turn off, repeatedly.
Unplugged unit, removed plate behind control panel, removed 5 or 6 wire connectors, pulled off burner switch knob and removed 2 screws that holds switch in place. Reversed the procedure and was done.
Parts Used:
-
Robert from Tonawanda, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old receptacle was burnt from lots of use.
Just cut the old receptacle wires and splice in new kit. Very simple and worked perfectly.
Parts Used:
-
Brenda from Scurry, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Parts Used:
-
Paul from Cornelius, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not heating properly.
Removed rear panel and removed switch. I placed wires from old switch to the new one. re installed switch an back panel.
Parts Used:
-
Joseph R. from Candia, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Wrong replacement Drip Pans installed previously caused damge to 8" Burner.
Removed burners and drip pans, replaced drip pans and re-installed burners. Simple....
Parts Used:
-
Lloyd from Pinellas Park, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Generic Drip Bowls Made The Burners Tilt.
Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.
Parts Used:
-
PATRICIA*NAYLOR from NEW PRT RCHY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The burner didn't work because it had the wrong drip bowl
Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.
Parts Used:
-
Leslie from Spring HIll, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken oven door handle due to pulling oven by handle.
Warning: Door falls apart after removing the two screws which attach the handle. No big deal, just a suprise!
Parts Used:
-
Dennis from Colchester, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Two drip Bowls needed to be replaced
No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!
Parts Used:
-
Robin from Boca Raton, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drip Bowl beyond cleaning
Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!
Parts Used:
-
Ann from Memphis, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drawer Glide Snapped Off And Broke
-
PATRICIA from GEORGETOWN, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the dial would not work unless the special screws, which are extra short, are utilized.
since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.
Parts Used:
-
Bruce E from Oxford, MS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
intermittant power to "burner" eye
due to the cooktop age, part was not an exact duplicate. I had to drill new holes in the stainless steel for mounting and ground wire. I used a lot of kitchen matches to heat the shrink tubes over the twist connectors. I should have gotten a heat gun or torch.
Parts Used:
-
don from Orange, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!