ACR2303MFW7 Amana Range - Instructions

LELAND from HERMISTON, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Broiler element not working

It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

Parts Used:

Broil Element

Normand from Lincoln, RI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The drip bowls were all caked and corroded.

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

Parts Used:

Terry from Mountain City, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Oven stopped heating, error message stated heating element

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Parts Used:

Lana from WATERVILLE, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven Temp inaccurate

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Parts Used:

David from BURNSVILLE, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Top burner would not turn off at any time.

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

Parts Used:

Donald from Byron, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

had for 2 weeks didnot work called for warinty they fixed stoped woking again about 18months later called them got price then bought though you.

first i turned off breaker . then slid out stove .usea cordless screwdriver totake off back then unplug switch then take off knob then take screwes out of front of switch theninstall new one revice method. took me longer to do this then to do the part

Parts Used:

Range Temperature Switch 240v

frank from pittsburg, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 18 people found this instruction helpful.

Was this instruction helpful to you?

large right front burner wasn't going on

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

Parts Used:

RUSSELL from LEESBURG, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

oven not keeping correct temp and sometimes would not relight when temp went dropped.t

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Parts Used:

Gary from PLUM CITY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

This burner on our range had no temperature control - it was either full-on or full-off

1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall

Parts Used:

Justin from BEND, OR
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Electric coil heat not controlable

Pulled the range from the wall and unplugged the power cord. Cleaned the floor behind and under the stove.
Removed the back plate of the control panel.
Pulled the knob off and removed the wiring, I took a picture of how the old controller was connected to make sure I put all the wires on correctly.
Removed the 2 screws in front the hold the controller.
Installed the new controller in reverse order. On ours the wires would only fit on one way so the picture wasn't necessary.

Parts Used:

Lesley from TROY, MO
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

Parts Used:

George from Irving, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Could not control temperature for 8" burner (front right).

The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.

Parts Used:

Sean from LISLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drip pans were not original to range, I could not get them clean.

I reoved old drip pans and installed new ones. Very easy, they look great!

Parts Used: