All Installation Instructions for Amana Range ACR2303MFW0

oven element burnt out

unscrew two screws..took old element out, put perfect fit new element in,screw two screws back in.

Parts Used:

JoAnne from Harrison, AR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Parts Used:

Range Terminal Block

Robin from Vanderbilt, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Drip bowls tarnished.

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Parts Used:

Chrome Drip Bowl - 8 inch

Jennifer from Albion, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Heating element would not get red hot

Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.

Parts Used:

Infinite Control Switch, 6"

James from Lewisville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bottom element burnt into two pieces

Unplugged stove, opened door and removed two bolts with a phillips screwdriver. Pulled out old element and pulled off the two wire leads. Replaced with new element and reversed all steps...wallaaaaa.

Parts Used:

Oven Bake Element

Maxwell from Springdale, AR
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Oven was not heating up to temp.

Pulled the oven away from the wall, unplugged the oven. Unscrewed the back panel(2 screws)that covers the pigtail connection. Pulled the two wires that attached to the heating element. Inside the oven i removed the two screws holding the element in place and removed old element. Put the new element in place and returned screws. The two wires clipped effortlessly on the back, returned cover and screws and plugged the oven back in. Tested the oven and returned it to its position, reset the clock and done.

Parts Used:

Oven Bake Element

charlie from glenwood springs, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

the boiler went out

Unpluged from electric. I took two bolts out of back of oven attached to boiler. Pulled out and exposed cords the attach to boiler. Slide them off and removed old boiler. Attached cords to new boiler and slide part back in to attach the two bolts back. Plugged oven back in and worked great

Parts Used:

Oven Bake Element

Angela from Little Hocking, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

top element was burnt out small burn hole in element

removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..

Parts Used:

Broil Element

Gregory from kissimmee, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Bake Element burned out

I found a video on YouTube and watched it showing how to change the element - then I performed the repair based on the instructions and recommendations in the video. The video had some good recommendations and cautions that helped ensure a successful repair.

Parts Used:

Oven Bake Element

Douglas from Elk River, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Oven Was Not Heating As It Should

Removed lower oven rack. Unplugged stove,removed 2 screws holding element in place,pulled element forward unplugged 2 wires. Reversed proc. To reinstall . Very simple. Parts were here in less than 24 hrs using standard shipping. Very good service

Parts Used:

Oven Bake Element

larry from springville, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Chared Bake element

Unplug oven, open oven door wide,pull out racks, clean reside that old element left. I used power drill with phillips head bit,pulled out old element, and disconnected wires from clips. Connected new element to wires, and Presto.Turned bake element to 300 deg.and waited only to see it red and ready to cook.

Parts Used:

Oven Bake Element

jon from lexington, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

bottom element was burned out

I was 100% happy with the whole process! The part arrived on schedule, it was exactly what I wanted! The best part of the story is I am a 77 year old lady whose husband was out of town and had never done this before. I could not have been happier with the process! Thanks again and I will use PartSelect again!!!

Parts Used:

Oven Bake Element

Bobbye from Ethelsviolle, AL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

oven temperature did not stay as set

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Parts Used: