ACR100WW (P1133384NWW) Amana Cooktop - Instructions

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

I followed the instructions provided.

came only I had to order the set again

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

I took the old wires and plug off and replaced it with the new block it works fine

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

Someone did the repair for me.

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.