ACM2160AW - Instructions

Easy! Just place it in the slot inside the microwave.Finished! Tah Dah!

replace old part with one one ordered from PartSelect

Just place it in the slot. . . . . 5 Seconds,,,no problem

Make sure 110v at the transformer. Activate switch controlled by the push button to open and close door. Push in the small metal arm on the switch with none metallic probe. If power is restored to microwave the switch is faulty and need replacement. One switch is not available, the whole 3 switch assemble has to be purchased.

Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!

Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.

1. Remove the trim frame off of the front of the cabinet (4 Phillips screws). At this point, take glass plate and turntable frame out of unit. 2. Slightly lift the unit off the cabinet frame (which is attached to the cabinet) so the feet on the microwave allow the unit to clear the frame and then remove microwave from the cabinet. 3. Once slightly removed from the cabinet, unplug the unit before completely removing it from cabinet. 4. Take 2 Phillips screws out of the side panels. 5. Take about 6-7 T20 Star Pin screws out of the back of the panel. (This may require you to purchase this special tip if you don't have it in your toolbox). 6. Slide the microwave cabinet toward the rear of the unit (the front portion clips into the frame ... don't try prying it off because you'll damage the unit). 7. Completely remove the microwave cabinet housing. 8. Be careful not to damage or catch any internal wiring inside the unit while the cover is off. 9. Turn unit on it's back and remove 4-5 Phillips screws holding the bottom cover in place. Remove bottom cover. 10. Now notice that the turntable motor is completely exposed. 11. Remove the wiring harness from the motor (notice which connection clip has the black wire). 12. Remove the one Phillips screw holding the motor to the frame. 13. Clean around the area in case food spills may have gotten into the area. 14. Insert new motor, put Phillips screw back in and attach power connection. 15. From this point on, just reverse steps to re-assemble microwave and put back in cabinet. 16. Test new turntable motor. 17. Enjoy the smile from your wife because she can now use the microwave!

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Information provided on the web site by Part Select, were helpful and encouraging to select and buy the part needed to repair the appliance. No doubt, a skilled person having background in the repair of appliances should attend such repair job.

Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.

removed microwave cover screws, unplugged motor, screwed on new one

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced