ACM2160AS (PACM2160AS0) Amana Microwave - Instructions

Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!

The repair went well...I am so glad that I read this info before buying a new microwave....it saved me lots of money. I did have a repair man come and look at it and he told me to buy a new one but it cost alot of money when it wasn't necessary. I did the repair and I was very proud of myself.
Three men watched a woman fix this and it was no problem...they were impressed also....

I looked up the #1 reason for no heat for my microwave on the site , and using my model number found that 92% of the time it was the Black Sleeve Diode. Ordered the $15 part, and installed it within 30 minutes. Most of the time was used for removing the built in microwave and removing the cover. Replaced the diode by finding it on the diagram that I printed from this site (free). Very relieved that we don't need to have our custom cabinetry re-sized to accommodate a new microwave. Thank you!

Used needle nose to pull off piece of old ring. Layed in new one.

I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

This had to be the easiest repair job on record. When the new glass tray for the inside of the microwave came from you, I just took out the old chipped one, tossed it in the trash and then washed and dried the new one and set it inside on the turntable rollers.

DONE in less than 60 seconds. I wash and dry FAST.

Thanks for having a web site that was so easy to find the replacement part.

Had a Trim Kit to remove, just 2 screws on the front to pull it out. Had to remove the tamperproof screws on the back (the outer shell is held on by them). I had to goto a local hardware store as nothing anywhere mentioned I needed this special tool (NOTE!!!!!!!) The bottom had normal phillips head screws. Note: I did not take the entire shell off, just bent it enough so the base plate could be pulled out. This exposed the motor, which strangely enough is NOT held in by any screws, just notches it slides in. Took the old motor out, came out VERY easily (only 1 plug to pull out). The new motors flange tab was bent a little bit so I had to use pliers to bend it back flat so it would fit in the notch on the bottom of the microwave (very easy). Overall A bit difficult due to special tool needed 9at least for me)

Took the cover off, had a lot of screws but easy. Removed the old motor and inserted the new motor. Replace the metal cover and it was ready to go. Can't believe I have waited so long to do this. I was going to replace the microwave but could not find the correct size to fit the cabinet.

Removed case,
Discharged HV capacitor and removed cooling fan.
Unscrewed ground end of HV diode and unplugged from HV capacitor.
Installed new diode by reversing the order. In my case, the problem was the magnetron was bad, so I replaced it as well.

Took out the old, put in the new.

I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!

Initially we started looking to buy a replacement microwave to replace our 13+ year old built-in microwave. It was a real pain finding a replacement to fit the exact dimensions. So I thought I'd try to find an old KitchenAid microwave. However, I was pleasantly surprised when this site came up on my search. Their website allows me to input the problems and then it showed two possible parts that needed to be replaced. I emailed tech support and asked them which part I needed. They responded very quickly and said I needed to replace the magnetron. I watched a couple YouTube videos and then pulled my microwave apart. It was incredibly easy to pull the outer cover off. The magnetron had 5 screws that needed to be removed and one electrical plug. Took me maybe 10 min to complete the entire repair. It was one of the easiest repairs I've done and so thankful for this site They saved me a ton of money from not buying a new microwave and we now have our microwave working again. In hindsight, I wouldn't hesitate. I'd order the Part now and get it fixed.

Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.