ACM1580AS-PACM1580AS1 Amana Microwave - Instructions

I had to unmount the over-the-range microwave oven to be able to gain access to the interior of the oven. Complicating removal (and re-installation) was the fact that there is a "pot-filler" faucet installed directly underneath the oven. In retrospect, I should've removed the faucet before doing the repair, but "c'est la vie."

After I got the microwave down, removing the case was also "interesting." I get bonus points for the fact that the previous owner must've had to replace the same diode before - and then re-assembled the microwave case incorrectly - thereby adding to the confusion (BTW, the service manual that I found online said nothing about how to remove the oven's case).

To remove the case, undo all the screws holding it on, and then rotate the case upwards from the back while also pulling the case backwards. There are crimped folds on the inside of the case that mate with the back edges of the front of the oven's chassis, and these folds have to be unclipped from the chassis in order to remove the case.

Replacing the diode itself was the easiest part of the job. The two connectors on the diode are of different types, making it impossible to install the diode with the wrong polarity.

BTW, the diode that had failed was not an OEM diode; I suspect it was a generic component that had been installed by a repairman sometime between 2004-2008 (when our home's original owners still owned the home). On the other hand, the new diode from PartSelect is an OEM part (it came packaged in a sealed Whirlpool bag).

The fact that the oven had stopped heating indicated that it was either the high-voltage diode or the magnetron that had failed. Since a replacement diode costs ~ 1/10th as much as a replacement magnetron, I figured it made sense to replace the cheaper part first. Fortunately, this fixed the problem.

One last thing: I tried testing both the old and new diodes for conductivity and polarity using my volt-ohm meter (VOM), but I was unable to get either diode to "turn on," even though my VOM is powered by a 9-v battery, and I used the 2-Mohm range setting. I guess the test voltage of my el-cheapo VOM isn't high enough to exceed the diode's threshold voltage, (even though I have successfully used this same VOM to test low-voltage diodes).

1. Order correct light bulb for unit and have it with you before removing old lightbulb.
My Microwave is built into cabinet.
2. Disconnect power (Either turn breaker off or unplug unit from wall)
3. Remove face cover on cabinet. (4 Phillips head screws)
I was able to reach in the opening in the cabinet and unplug from the wall.
4. Remove Phillip head screws holding microwave in cabinet.
5. Remove microwave from cabinet.
6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover.
Light bulb is on the top front right side.
7. Remove 1 philip head screw holding light bulb and unplug quick connector wires.
8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place.
9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet.
10. Reverse order 5,4,Plug unit in wall before putting the face back on.
Done.

Pulled unit out, pried the bottom plate off the unit. Mine was not screwed in, but designed to be pried off, and then replaced. That was a surprise, but not very difficult. Unscrewed the motor, unplugged the electric connection, replaced it with new part . Replaced the bottom plate and tested the machine.

removed a dozen screws-discarded large cap-replaced diode-replaced a dozen screws(took longer to replace them than remove for some unknown reason). Microwave now works(wife happy).

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.

There were two hard parts for me to work through.

The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.

The second hardest part for me was finding the correct replacement bulb on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.

Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.

Thanks PartSelect!!

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

ordered a new tray

Did an online search for repairs and found PartSelect. Simple to order the part and had it installed myself less than a week later. Thank you!!

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.

OMG! I wish everything in life were so easy.....The cooking tray of our 15 year old microwave cracked and I swore it'd be impossible to find a replacement. That is until I discovered Partselect.com!!All I had to do was input the appliance brand and part I was looking for, and there is was. Thank you, Partselect.com!!

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott