ACF3355AS Amana Range - Instructions

Replaced the igniter as I've done with other products with similar problems. My amp tester wasn't working so I didn't test the igniter. The igniter wasn't the problem so I contacted a repair man who came up with the conclusion that the problem was actually the gas control valve. The valve wasn't letting enough gas to ignite the burner.

I'm a girl, blonde, and fixed it! Oven just turned 10 in July. I removed oven racks, then used screw driver to remove two screws for the lower panel. Used screw driver to listen the two screws that hold igniter in place, then wrench to remove. Pulled wires out from hole in back of oven, unplugged old igniter, used needle nose pliers to hold wires in place from slipping back through hole, plugged in new, pushed wires back in, screwed it in, turned oven on to make sure igniter worked, it glowed, turned off, replaced lower panel, turned oven on again to let it light up, it did, screwed it in, replaced rack, closed door, preheated oven, and then baked cookies! Great company, great customer service, and super fast shipping!

got new horizontal igniter from Parts Select pulled stove out from wall unplugged old igniter took out bottom oven pan loosened two screws. used same two screws to put new igniter in place, put back bottom oven pan pushed bake button on front of oven and the old was lioke new again

Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.

Remove two phillips screws, lift the burner head up and remove the wire from the electrode. DO NOT DROP THE WIRE!!! It will fall into the stove top, adding much more time and frustration to this very simple repair. Reverse these steps to complete the repair.

I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.

Replaced both the broiler (top) oven ignitor and bake (bottom) oven ignitor! Easy to do, no need to call a repair person on this job!

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

The broiler igniter and oven igniter are the same - WITH ONE MPORTANT DIFFERENCE- the plug! I tried to just switch them since we dont ever use the broiler but could not, due to the plug. I think that is part of planned obsolescence ! Anyway, I left the door and the power on - you guessed it, rebel! If you get a tingle from replacing this part you shouldnt be trying to fix it on your own! I removed the oven racks, took two small screws from rear of oven floor out, removed base plate. Two more small screws released the defective part. Pulled the plug wire through the back of oven and unclipped the connector. Plugged new part in, tucked the wires back into the insulation, replaced two screws on the igniter. Test fired oven- worked like a champ. Shut burner off, reinstalled base plate and screws and put the oven racks back in. Easy!

Took off the bottom panel of the oven two screws then unpluged old igniter then pluged in the new igniter, replaced the bottom panel and that was all. I didn't even have to take the oven door off. Repair was done in less that 5 min.

Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.