ABR2527FES12 Amana Refrigerator - Instructions

It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.

well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did.
the trick was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Snapped new cover on.

4-Screws 3 plactic hoses to remove pull 3 tubes out and instol new part last then 15 min. Making shure is no leaks. Easy

Wife learned you can overload the cheese and fresh veggie trays and the plastic rails broke. Repair required removing parts from the old crisper frame -- no experience and no instructions. Had to study broken part and figure out how to remove parts. Released catches with a knife and, by trial and error, figured out how to install rescued components on new crisper frame with minor damage and frustration.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

lift glass, slide new rail in replace glass. 2 min repair.

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

To keep from having to pay the appliance repairman $100.00 for a diagnostic fee I just started replacing parts that were known for causing this problem. First I replaced the compressor switch and capacitor that didn't work so then I replaced the damper controller then I replaced the control board then I saw that the evaporator fan wasn't spinning so I replaced the evaporator fan motor and the bimetal defrost thermostat. That was the problem I wish I would have checked that first. But it works like new now.

First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

I watched the video provided on-line in your website, which was excellent. The information provided gave me everything I needed to change the board. I already had experience handling control boards and was aware of the static precautions; however, your paperwork was very good detailing how to program the new board. The only small problem I had was reinstalling the temp sensor in its bracket. The lead was very short. Other than that, all went well! The project took between 20 and 30 minutes.

I watched video for repair and it went just like it showed. piece of cake

Replaced the electronics board. Fairly easy job. Video helped enormously. Programing is awkward.