All Installation Instructions for Amana Refrigerator ABL2227VES3

changed the light bulb still would not work so I figured it was the switch sure enough.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Parts Used:

Refrigerator Door Switch

anthony from HAVELOCK, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I had a loose fitting old condensor fan blade on my new motor.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Parts Used:

Fan Blade

Roger from SMITHFIELD, RI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Water not draining to pan. It caused an ice build up under the freezer draw

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

Parts Used:

P-Trap Drain Tube Kit

Rich from WINSTED, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

defective light switch

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Parts Used:

Refrigerator Door Switch

THOMAS from WILLARD, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I purchased a display model that was missing a part.

Snapped on the new toe grille.

Parts Used:

Refrigerator Kickplate Grille

Monte from Longview, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Boyfriends freezer door wouldn’t shut completely

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Parts Used:

Drawer Gear Kit

Megan from NORFOLK, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

broke my original Kickplate Grille

knelt down, positioned replacement kickplate; popped into place, stood up!

took longer to open the box and peel bubble wrap off item than to replace it!

Parts Used:

Refrigerator Kickplate Grille

Daniel from GEORGETOWN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Door light switch disintegrated

Very simple fix, remove 3 screws, two connectors to the old switch

Parts Used:

Refrigerator Door Switch

Thomas from Roseville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ladder hooks broke

Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max

Parts Used:

Crisper Drawer Cover Support

Miguel from ESCONDIDO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The center rail was broken

The part just snapped in. super easy.

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Joella from THE DALLES, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Gasket not sealing good

Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.

Parts Used:

Door Gasket - Black

Vince from Miami, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Parts Used:

Refrigerator Electronic Control Board

Marc from SEASIDE, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator was warm,freezer was cold

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

Parts Used: